Showing results: 91 - 105 of 501 items found.
-
-
-
Alpha Automation Inc.
This machine is used to test back planes used in telecommunications central stations. An operator loads a completed point to point wired back plane onto a retractable shelf on the front of the tester. Table continues and the disk falls through a hole into the bin. The shelf is pushed back into the machine where it is held in place by pneumatic operated clamps. Then a series of pneumatic cylinders sequentially insert a test card into each location in the back plane. A remote instrument performs a complete point to point continuity, short and hi pot test on all connections in the back plane.
-
SYD' -
Chongqing Lushun Scientific & Technological Development Co., Ltd.
The instrument is designed and made as per the National Standard of People's Republic of China GB/T3536-2008 "Test Methods for Flash Point and Fire Point of Petroleum Products (Cleveland Open Cup Method)". It is suitable to determine flash point and fire point of petroleum products and asphalt, excepting fuel oils and petroleum products having open cup flash point lower than 79 C.
-
MTQ Testsolutions AG
Within the test strategy the final functional test complements the quality strategy. Therefore meaningful results of functional tests shouldn't be focused only on good/bad selection. Goal is to get correct data for statitistics and trend analysis.Under economical point of view you should consider following points as very important in test conceptions:Stability of measurementsAccuracyand the throughput
-
T1000-37 -
Tesuto Systems
T1000-37 breakout box is our most versatile model, using dual 37 pin D-Sub connectors for signal capture or monitoring. Dual connectors provide a total of 74 test points plus a ground jack. All test points use standard size 4mm banana jacks. Test points may be connected using shorting banana cable to allow signal continuity. Ideal for continuity measurements, isolation testing, and signal capture.
-
K8218B -
Keysight Technologies
The DriveThru feature enables the test development software to test integrated circuits or connectors when there are no test points assigned between the resistor and the device.
-
K8218A -
Keysight Technologies
The DriveThru feature enables the test development software to test integrated circuits or connectors when there are no test points assigned between the resistor and the device.
-
CKT1175-10 -
CK Technologies, Inc.
Designed for wiring testing requirements requiring up to 2,000 test points, the CKT1175-10 is ideal as a benchtop or portable test system. The system is packaged in an enclosure specifically designed to be used in rugged environments. The basic 500 test point system is 20.5 in. (521 mm) wide X 12.0 in. (305 mm) high X 16.05 in. (408 mm) deep; the 500 test point expansion units are 20.5 in. (521 mm) wide X 6.00 in. (153 mm) high X 16.05 in. (408 mm) deep.
-
YAVTB000 -
6TL Engineering
When wiring a test fixture, you often have a need to join three or more wires onto the same test point. This module solves this problem, adding test points for manual test probes and a 4 position DIP switch. Circuits 1 and 2 feature up to 5 poles in parallel to increase the space for power supply terminals.
-
CKT1175-20 -
CK Technologies, Inc.
The CKT1175-20 is a high-voltage wiring analysis system that features rack-mounted switching matrices. This system is expandable in 100 test point increments to 96,000 test points, and available with a wide variety of adapter cable interface connectors, with the standard interface being the CKT MAC interface system.
-
TOPTEST GmbH
DrillView is used to create and display test point plans from Cad data
-
-
4183 CP -
Standard Electric Works Co., Ltd
● Safely operates at low voltage ● Measures system voltage.● Measures capacitance of test point if system voltage is known.● Checks phase rotation of cables.● Phases out cables.● Rugged - comes with portable case.● Operates from potential test point of elbow connec-tors.● Battery operated.
-
National Technical Systems
Flexural Strength Testing is used to determine the flex or bending properties of a material. Sometimes referred to as a transverse beam test, it involves placing a sample between two points or supports and initiating a load using a third point or with two points which are respectively called 3-Point Bend and 4-Point Bend testing.